参数
以上芯片适用于：Lexmark MS711dn / MS811
适用机型
Lexmark MS711dn / MS811
使用方法
- 关闭打印机电源，打开前盖或侧盖，取出旧粉盒。
- 沿正确方向拔出旧芯片，避免触碰芯片触点。
- 将新芯片对准插槽方向装入，确保触点朝下、卡扣到位。
- 装回打印机后，打印机应能正常识别芯片并复位计数。建议打印一张测试页确认计数已正确复位。
使用注意
本说明为粉盒芯片，注意加满碳粉后再更换芯片，否则芯片不生效或会提示数值不满。
要确保硒鼓完好状态下更换，才不容易出现代码报错。
在使用和安装芯片时（特别是秋天干燥环境），需要先去除人体静电或佩戴防静电手环，以防击穿芯片。
版权声明
本公司生产/销售的芯片为兼容芯片，与原装品牌并无直接关联。\n
公司介绍
彩一办公耗材，公司成立于2008年，主要业务涉及打印机芯片、硒鼓、粉盒、碳粉等配件业务。
Specifications
The above chip is compatible with: Lexmark MS711dn / MS811
Applicable Printer Models
Lexmark MS711dn / MS811
Installation Instructions
- Power off the printer, open the front cover or side cover, and remove the old toner cartridge.
- Pull out the old chip in the correct direction, avoiding contact with the chip contacts.
- Align the new chip with the slot direction and install it, ensuring the contacts face downward and the retaining clips are properly seated.
- After reinstalling the toner cartridge into the printer, the printer should recognize the chip normally and reset the counter. It is recommended to print a test page to confirm that the counter has been correctly reset.
Usage Precautions
This instruction applies to a toner cartridge chip. Please ensure the toner cartridge is fully filled with toner before replacing the chip; otherwise, the chip will not take effect or the printer will prompt that the toner level is insufficient.
To avoid error codes, please ensure the imaging unit is in good condition before replacing the chip.
When handling and installing the chip (especially in dry autumn conditions), please discharge any static electricity from your body or wear an anti-static wrist strap to prevent damaging the chip.
Copyright Notice
The chips produced/sold by our company are compatible chips and are not directly associated with the original brand.
Company Profile
Caiyi Office Consumables was established in 2008. Our main business involves printer chips, toner cartridges, imaging units, toner powder, and other consumable accessories.
#打印机芯片,碧砚,利盟,粉盒芯片,耗材
Specifications
The above chip is compatible with: Lexmark MS711dn / MS811
Applicable Printer Models
Lexmark MS711dn / MS811
Installation Instructions
- Power off the printer, open the front cover or side cover, and remove the old toner cartridge.
- Pull out the old chip in the correct direction, avoiding contact with the chip contacts.
- Align the new chip with the slot direction and install it, ensuring the contacts face downward and the retaining clips are properly seated.
- After reinstalling the toner cartridge into the printer, the printer should recognize the chip normally and reset the counter. It is recommended to print a test page to confirm that the counter has been correctly reset.
Usage Precautions
This instruction applies to a toner cartridge chip. Please ensure the toner cartridge is fully filled with toner before replacing the chip; otherwise, the chip will not take effect or the printer will prompt that the toner level is insufficient.
To avoid error codes, please ensure the imaging unit is in good condition before replacing the chip.
When handling and installing the chip (especially in dry autumn conditions), please discharge any static electricity from your body or wear an anti-static wrist strap to prevent damaging the chip.
Copyright Notice
The chips produced/sold by our company are compatible chips and are not directly associated with the original brand.
Company Profile
Caiyi Office Consumables was established in 2008. Our main business involves printer chips, toner cartridges, imaging units, toner powder, and other consumable accessories.
